VictorMN's Mitsubishi Triton GLX-R
|
|
• Make: |
|
Mitsubishi |
• Model: |
|
Triton |
• Series: |
|
GLX-R |
• Year: |
|
2012 |
• Transmission: |
|
Manual |
• Owned
since: |
|
02/2012 |
• Location : |
|
|
|
|
Modifications |
Weather Shields front Front windows tinted. Auxiliary Gauge Set. Towbar Package. Dust seal kit for tail gate. Rubber mat tray. Tray bed rear tail gate liner. Canopy. Dash Matt. Triton Door Handle Recess Plates. Triton Front Windscreen Sunshade film. USB Charger. Interior Mirror with Reversing Camera Reversing Sensors. Reverse spot lights Narva 71860. Embroidered Carpet Mats. Stainless Steel Outer Scuff Plates fr & rr. ARB Deluxe bulbar. ARB Under Vehicle Protection bash plate ARB Snorkel.. ARB Old Man Emu Suspension. Beaudesert 2 ¾ Stainless steal Exhaust Lube change - Rear Diff,4lts Nulon full synthetic. Stein Bauer Chip. Sprint Booster. Woolly fleece seat covers Fr & rr. GME UHF Radio 80 channel. Trailer Brake System. Passenger seat raised 8mm, Oil catch Can fitted, ERG Blanked off. Hella 100w Spot lights with Blue filters. Pollen Aircon Fliter (MZ341012EX). Rear diff breather mod. Genuine Alloy Sports Pedals. Long Ranger fuel Tank 126 lts. BlueMax 2, Boost & EGT Guage. Mickey Thompsons ATZ 4-Rib. 265/70/17. |
|
Future Modifications |
|
|
|
|
Other info: |
|
1. ARB Old Man Emu Suspension - great ride, shame about the clearance, ie; front 10ml rear 20ml, If I'd known I would have got something else with more clearance.
2 Rear diff oil changed, factory says 2.1 lts,I put in nearly 4lts, had to travel to the shop and get more with my diff only half full. used Nulon full syn.
3 Rear Dust seal kit for tail gate - what a joke, unfortinaly you need it to keep dust out if you got a canopy. not a problem on other 4x4's.. starting to fall apart as it's only plastic.
4. Reverse camera & sensors- must have, Tritons with canopys are incredably hard to see out off when reverse parking.
5. Beaudesert 2 ¾ Stainless steal Exhaust- 10/10 fits & works well, also has a hole for your EGT to go straight in..
6. Stein Bauer Chip- 9/10, Shame there is no one local who can tune it. otherwise it works great..
7. Sprint Booster- another must have if you like quick throtle response.
8. Oil catch Can.-must have if you want to keep your engine clean internaly.
9. ERG Blanked off- same as above.
10. Pollen Aircon Fliter- worth it, keeps your aircon clean and smelling nice.get the factory one first as it has fitting instructions and were to cut it, then you can buy cheaper aftermarket filters later on.
11. Rear diff breather mod- What was Mitshubishi thinking when they put that on, change it ASAP.
12. Long Ranger fuel Tank- so far so good, nice not to be filling up every 4 or 5 days.
13. Lube Change - Manual Gearbox nulon full synthetic. Makes a differance for shaw, easier gear changes and no more crunching when you go for reverse.
14. Lube Change - Brake & Cluth fluid. Must Do. firmer feel on brakes. we had to suck out all the crud that were in both cylinders and flush the lines. Don't know what fluid they use but it resambled mud on the bottom. only had 20,000 ks on the clock.
15. Lube change - Power steering, noticed no differance when driving. but same as above the red fluid had lots of dark stuff in it.
16. BlueMax 2 Boost & EGT Gauge - really happy with it, surprized how quick the exhaust temp changes. LED temp lights died out after about 2years. Boost guage still working good.
17. Thompsons ATZ 4-Rib fitted 28000ks 15/06/13. +s no slipping off & on the road. - On the Noisey side though,, expensive. Speedo reading at 100ks = 102 by GPS. was spot on with standard factory tyres. Warrenty Jobs: 1. Cause; Over boosting & tripping out engine when I go above 150ks Fixed; They replaced Turbo unit, 2. Seat belt warning light.fixed. 3. Clutch slipping, ongoing, 4. 30 000K service $590.00 ouch. 5. 45 000k service $ 536.00 also included 1. lower control arm inspection Bulleton-010067. 2. wheel alignment & Balance. 6. |
|
|
Harty
|
|
Comment:
|
12/08/15 |
|
sry now read down as to what u did
|
Harty
|
|
Comment:
|
12/08/15 |
|
Hey mate I am also interested on how you did your rear diff breathers as I to have the little white cap with no fitting
|
VictorMN
|
|
Comment:
|
29/05/14 |
|
Through the front driversside fire wall, drill a hole put in a rubber gromet. other wires go through the same spot, like for my spottys and boost guages.
|
adelaideMN2010
|
|
Comment:
|
29/05/14 |
|
Hey mate - nice car. Can I please ask where you ran the wiring into the cabin for the reverse lights in the rear bumper? I just bought the same Narva 71860s and want to mount the switch next to the ASC button. Just need to know where to gain entry to the cabin!
|
Waldy
|
|
Comment:
|
26/08/13 |
|
Hey mate ignore my comment sorry I was reading down the page
|
Waldy
|
|
Comment:
|
26/08/13 |
|
Hey mate I am also interested on how you did your rear diff breathers as I to have the little white cap with no fitting :(
|
VictorMN
|
|
Comment:
|
28/07/13 |
|
No side affects at all, Did notice a slight improvment just of idle. Done just over 30.000K with it blanked and havn't looked back. Mitsubishi has never said anything when I got it serviced.
|
brodical
|
|
Comment:
|
28/07/13 |
|
Hey mate just wondering if you have had any side effects from yor egr blank? Cel? Limp?
|
VictorMN
|
|
Comment:
|
06/11/12 |
|
I used Narva Compac 100mm fog lamp kit No; 71860 as these spreed the light out not like a spot light. you can drop the hole rear bumber to work on only 4 bolts and disconnect wireing, I used a small chisal to knok out the plastic hole witch is already marked out from the factory. Shame I couldn't find the factory lights for this as they would just bolt straight in. With narva lights you have to be a little inventiove to fit them in but it can be done, I also fitted a switch so that I can switch them of when in town so that I don't get any unwanted attention from the cops.
|
Calblitzen
|
|
Comment:
|
05/11/12 |
|
Nice rig. How did you mount the rear lights in the bumper, and what type are they
|
VictorMN
|
|
Comment:
|
12/09/12 |
|
Easy done, I ordered Part No: 3713A037 from mitsubushi, cost about 9$, when I picked it up I ripped off the little steal cap. went to supercheap auto and got about a meter of hose to fit were the cap came off. you can then put a breather or little fuel filter on the end of the hose Zip tye it up high out of the way, pull the old breater out put a little silastic on the new one and your done.
|
buddha
|
|
Comment:
|
12/09/12 |
|
Nice , can i ask what you did for the rear diff breather? Very happy with my 2012 MN but am stressed it wont cope with water crossings with the little white cap?
|
Note: You must be logged in to place a comment on this profile.
Please log into the forum here!
|
|
|