What did you do to your Triton today?

[Steane]

Installed EGT monitor, up and running, except for the Thermocouple - I need to buy the 1/8 NPT tap to drill/tap the Thermocouple into the dump pipe
Always something...

hey Schmuck what did you stick the thermocouple in to know it is working?

.... In my anoos.

Don't get upset, it's the answer you were looking for

Too much blow-by putting it there Schmuck

[motoz]

Had the roll bar powder coated black during the week. Did a trial fit of my RTT and rack.



Have left a gap to fit a 33" spare, with Maxtrax and Hi Lift on either side. I should be able to fit 1x 20lt fuel can there also.

I'll make up the mounts and brackets during the week then off to the powder coaters.

[motoz]

A couple of setup snaps...

[dan.batto]

Looking very good mate!!!

[Steane]

Big fluff and buff for Matilda today. A few hours with the Festool got rid of the bush pinstripes, followed up with a few layers of Zaino wax. She now looks like a supermodel again

Tomorrow I'll be revisiting the fitting of the Razorback canopy that was never done right in so many ways (even by their recommended fitter) They were paid $200 to stuff it up, so I'm going to pay myself $300 to do it right and then treat myself to something fancy. Might get one of those pie and coke specials down at 'The Boardroom'

[Froggy]

What is a festool?

[dan.batto]

Double post - damn tapatalk

[dan.batto]

What is a festool?

It's a brand of tool.

Mate your wasting your time! Although there is a fantastic silver ml in my drive waiting to have that done I my drive if you have a spare day to fly here an do it? I'll pay you....

[tezza08]

Made sure the old boy had enough room after the draws went in:) ........... He gave me the paw of approval



---
I am here: http://tapatalk.com/map.php?cq5slq

[Steane]

What is a festool?

It's a brand of tool.

Mate your wasting your time! Although there is a fantastic silver ml in my drive waiting to have that done I my drive if you have a spare day to fly here an do it? I'll pay you....

Festool make power tools froggy (like Dan said), in this case a very cool polisher/sander.

I've seen your pin stripes Dan, and the only way those can be fixed is with a spray gun and compressor

[mattz]

What is a festool?

It's a brand of tool.

Mate your wasting your time! Although there is a fantastic silver ml in my drive waiting to have that done I my drive if you have a spare day to fly here an do it? I'll pay you....

Festool make power tools froggy (like Dan said), in this case a very cool polisher/sander.

I've seen your pin stripes Dan, and the only way those can be fixed is with a spray gun and compressor

Do you wanna do mine then.

[Steane]

Wouldn't suit Bella to be all shiny and new looking. You know she's not that sort of a woman Mattz.

[dan.batto]

Sounds like mattz is in the same boat as salt!

On topic, I looked at ordering my dig options unit! ... What house
No I didn't pay for this mod, bel's parents basically are for all the work I have done at their rental
Property renovating it!

[Diablo]

Fitted my new Scotts Rods 3" exhaust today Sounds pretty beasty now, and the turbo spool from a standing start is greatly improved

What a mission to remove the factory exhaust system. Jebus the bolts on the dump pipe were tight and hard to get to.

[deermaster]

That looks good, how much noisier does it make it? I must be growing up as I like mine pretty quiet now. Can I also ask what the brass bolt is in the exhaust?

[Diablo]

That looks good, how much noisier does it make it? I must be growing up as I like mine pretty quiet now. Can I also ask what the brass bolt is in the exhaust?

The exhaust note is definitely louder and deeper. But not offensively loud. Have not had it on the hway yet so not sure how she will be at causing speed. The brass bolt is for a future pyro sensor

[Homer]

Very nice Geoff, as is Tezzas drawers

So many mods on the cars on this site...you can watch one drive past and it will be completely different to what you're driving

[NTBB]

I didn't realize the oem zorst has no flex joint... Is this a $$ thing from MM or is it not needed...

[Diablo]

Be $$ as to why it's not there. The factory exhaust is really really cheap when you compare it to the replacement one. Also the factory gaskets (except the dump pipe) had nearly discentergrated too

[coxy47]

I installed the new exhaust. Nicer to drive as it more then makes up for the torque loss from the 32's and it gives it a nice note.

[Diablo]

Good to Hear you got the dump pipe bolts sorted mate

[Sky Miner]

Gave her a good clean in and out just so i could drive her back on the red muddie roads again

[coxy47]

Good to Hear you got the dump pipe bolts sorted mate

Yep. I ended up doing the same as you and using the trolley jack handle as a lever

[Diablo]

There is just no bloody room in there to get a decent spanner let alone enough torque on it to move the freakin bolt

Glad I could help. Next time (not that I ever plan of replacing an exhaust again) I'm going to follow homer and fridgie's suggestions and presoake the bloody nuts

[coxy47]

I had done that and mine were still seized.