What did you do to your Triton today?

[peterdeg]

Put on the Bushskinz intercooler guard.


Had to remove the air guide to make it fit. Next weekend's job will be trimming the guide to fit and putting it back!
(The plate behind it is the genuine, heavier duty 'under body protector' one)

[Sky Miner]

Installed 2 new recovery points

put new EGR plate in....dunno why just did it

Relocated provent to front of the vehicle

That enough for one weekend 'Gonna drink freezing cold rum now and enjoy what's left

[patto]

Well i finally swapped out my front struts that i bought off ag911 years ago - one word of advice every now and then i reckomend that you remove the rubber plug ontop of the strut mount and give it a good spray with wd-40 or something. The strut shaft and nut had rusted that badly i had to sacrafice an old screw driver and weld it to the shaft of the strut and the sacrifice a 17mm spanner by welding it to the nut in order to crack it. it was a prick of a job.. the rest of the install was a piece of p!ss..... with the new struts in i greased up the top of the strut before putting the top plug back on.

[Cowboy Dave]

Didn't achieve too much today. Got out the Dremel and tidied up the flare cuts above the bullbar. The old cuts weren't too bad considering I did them with a little hand saw as a bit of an emergency repair at coffs. Anyway the cuts are pretty straight now. That and I have plastic dust all through my hair

Then I cut some pinchweld and whacked that on to make it all look tidy. Having done that I broke out the Mitsubishi touch up paint and tried to patch up the bits on the bar where the flares had rubbed off the paint through to black. Looks better than it did but I'd have to concede I didn't do a great job of it.

[TUFF TROOP]

I got it muddy and gave it absolute hell through the mud holes around here. Also found a awesome swamp which almost got stuck in. Water level ended up around my mirrors at one point haha whoops.

[wake jake]

Installed genuine neoprene seat covers pricey but nothing else fits well and installed ipod cable too, finally no more cd's

[Mooons]

Sat in a wombat hole for nearly 10 mins with the smelly soup level 1/3 of the way up my doors while i waited for my new found friends of the geelong 4X4 club to recover me
happy to say door seals held up well
and the only vehicle to make it through was a hilux with 35s & a 7" lift
what was i thinking

[dan.batto]

I want photos mate!

[fraz91]

the only vehicle to make it through was a hilux with 35s & a 7" lift
what was i thinking

Sounds like someone forgot about their magic buttons Either that, or needed a little more right foot

[Mooons]

the only vehicle to make it through was a hilux with 35s & a 7" lift
what was i thinking

Sounds like someone forgot about their magic buttons Either that, or needed a little more right foot

Buttons on
sitting on my guts
as soon as i jumped in could feel every thing hang up
Damn abr bar
muddies were like paddle wheels
carpet is still clean

[Mattstruck]

Sounds like a Batto hole mate

Where did you go?

[Mooons]

wombat state forrest west side
hadn't been that side before

[dan.batto]

I cleaned half the mud an crap from my radiator

[dan.batto]

I cleaned half the mud an crap from my radiator from the last "batto hole". I'll have to give it a good underbody wash before I book it in for the 90,000km service tomoz!!

Also replaced the face to my driving light switch as well as fixed the wiring to work properly! As well as that I made my mud flap protector thingy (will fill you in more when it's done) fit and sent it to my fabricator (uncle) to make the other side.... Hopefully no more busted inner guards


---
I am here: http://tapatalk.com/map.php?eom21k

[Mattstruck]

mate im hanging to hear more on these Group buy

[bill65]

clean out manifolds & rebuild turbo on spare motor.now clean my out..strip spare transfer for reduction gears

[bill65]

wombat state forrest west side
hadn't been that side before

west side is the best side

[motoz]

Broke the inner LHS wheel arch splash guard in half reinstalling it after fitting the engine bay light.

The thing was so brittle it snapped in half. Are these easy to get and what do they cost?

[dan.batto]

Are you talking about the inner guard in front of the washer bottle? If so yes easy enough to get. I thinking paid $40 from my local stealer, they had them in stock! I'm going to get the rhs tomoz!

[motoz]

Yes mate that's the one. Thanks for the reply will pop past the dealer tomorrow.

It would be good to make some rubber ones though as that plastic is a little pox.

[dan.batto]

I'll throw up a post soon with what I have in plans.... Pics an all, just have to wait til my uncle returns what I have done, should stop these breaking I hope

[Snooozy]

wired up a twin cig lighter socket for GPS. got sick of the wires running down the dash.

I will put details in my build thread

[borngeek]

After 8 months, 20,000Km and about 8x 4wd trips..
I removed my play tyres for my daily driver AT's

//Retired from 4wding now

IMG_20120506_145635 (Small).jpg

IMG_20120506_144938 (Small).jpg

IMG_20120506_143931 (Small).jpg

[fraz91]

//Retired from 4wding now

Surely you can't be serious?!

[Sky Miner]

//Retired from 4wding now

Surely you can't be serious?!

He's delirious not serious