What did you do to your Triton today?

[kxboss]

Installed new inter cooler hose

[tezza08]

Ordered new rims and tires today, Kumho MT51, 285/75/16 and black sunrasiers 16x8 zero offset.
5 of each

Got them on today!


Sent from my SM-G935F using Tapatalk

[braydenc]

Ordered new rims and tires today, Kumho MT51, 285/75/16 and black sunrasiers 16x8 zero offset.
5 of each

Got them on today!


Sent from my SM-G935F using Tapatalk

can you take a side on shot mate?

[ag9111]

Ripped out the noisy 3" SS Exhaust and replaced it with a much quieter 2.5" SS with muffler & Cat.

Have done about 50km city driving and the car is smoother at lower revs now. No where near as rough.
And a heap quieter.

Now a Unichip to hopefully quieten the injector rattle.

[als1200]

Ripped out the noisy 3" SS Exhaust and replaced it with a much quieter 2.5" SS with muffler & Cat.

Have done about 50km city driving and the car is smoother at lower revs now. No where near as rough.
And a heap quieter.

Now a Unichip to hopefully quieten the injector rattle.

Where did you get that from?

[ag9111]

A local exhaust shop in wollongong
These guys have been around for years. In the mid 80s they hand built the extractors for my 18RC to 18RG conversion on my first hilux 4wd

[tezza08]

Ordered new rims and tires today, Kumho MT51, 285/75/16 and black sunrasiers 16x8 zero offset.
5 of each

Got them on today!


Sent from my SM-G935F using Tapatalk

can you take a side on shot mate?

Here ya go


Sent from my SM-G935F using Tapatalk

[coughy]

A local exhaust shop in wollongong
These guys have been around for years. In the mid 80s they hand built the extractors for my 18RC to 18RG conversion on my first hilux 4wd

oh memorys there garth 18rc and 18rgeu i had mmmm nice to rev the pick handles out of
i had a 18rg head that i modified and put in 2v clevland valves thos MF where huge but i made them fit handy when u worked in a reconditioning shop that was my play time after work lol it went hard and stroked to a 2.6 with sigma dome top pistons and i think had nissan rods long time ago but yer oh the fun times
would pull the front wheel of the ground when on the hwy in 5 dropped back to 3rd and pegged up to 9700rpms hehehehehe

oh thanks for the memory reflash m8

[ag9111]

My RC was biult by me in the garage.
Pretty tame with only lumpy cams and a 40mm Dellorto carby on a lynx manifold but it snarled and crackled and wasn't to bad for what i had done.
The RG was not quite blueprinted but wasn't far off.
Upgraded ported yamaha head and lumpy cams. Twin SU's i think was the last version before i moved it on.
Would do 8500rpm with more to go.
Shoot flames out the exhaust on deceleration and was awesome of the lights
Would light up both 10.5R15s with ease.
Unfortunately it would not idle under 1300rpm and didn't make any useful grunt till about 2800rpm.
Not real good in a 4wd

[RHKTriton]

Bought the new clock spring.

Now just got to get it in so the new airbag can be fitted.

[har05l]

Fitted a new SPVi heavy duty clutch due for official release soon




Sent from my iPhone using Tapatalk

[Merts]

Grabbed a $2 army surplus peg bag from Aussie Disposals, broke out the sewing machine and added some Velcro. Perfect size for all of the pegs, ropes and adjustable straps for my brand new Darche 270 awning (which I fitted yesterday- photo in my build thread).

IMG_0885.JPG

[NowForThe5th]

Took it over to Leethal, got him to give it a good going over and changed all the fluids to better quality then the stuff my local misty dealer had been dropping in. Also got a quote for dropping the box & getting my stupid noisy clutch bearings looked at. Principal dealer wanted the car for three days & lee's can do it in one. I know where I'm headed particularly when I'd rather pay for it and have it done properly then shoddy warranty work.

Also has my new shiny bits fitted

Road Safe & bushskinz intercooler sump & tranny combo

http://imghostr.net/image/FzfU
http://imghostr.net/image/FkOY

[Jacobie]

Took it over to Leethal, got him to give it a good going over and changed all the fluids to better quality then the stuff my local misty dealer had been dropping in. Also got a quote for dropping the box & getting my stupid noisy clutch bearings looked at. Principal dealer wanted the car for three days & lee's can do it in one. I know where I'm headed particularly when I'd rather pay for it and have it done properly then shoddy warranty work.

Also has my new shiny bits fitted

Road Safe & bushskinz intercooler sump & tranny combo

http://imghostr.net/image/FzfU
http://imghostr.net/image/FkOY

Nice mate!
I've been going to Lee for the last few services on my car, always good to deal with and know it's in capable hands! Well worth the journey from Ipswich

[dieselweasel]

Sounds a bit lame but i topped up the oil!

First time since ive had the ML wheelbarrow. Never needed to top up in between services before. I know its because i fitted the manual boost controller. Wondering if i need to lower the psi a bit, 3rd and 4th gear reach 18 and a decent foot thud in 5th gear will reach just over 19psi. Im having too much fun now to go back but maybe a compromise is needed?

[4wd26]

New tyres

[Dave]

Nice looking wheels mate

[JamoGLXR]

Nice looking wheels mate

Are they FJ Rims?

[4wd26]

Nice looking wheels mate

Are they FJ Rims?

Yeah fJ cruiser rims +15 offset

[dk064]

Brought a secondhand 2014 GLXR 2 weeks ago finally got my USB plugs in new stereo in cleaned the MAF sensor as it was 15ish around town (now showing as 11) put on a coat of nupolish to prevent the summer bat poop eating my paint and I'm now buggered lol , still need to put new wipers on the Mrs car but they are $37 each at supercheep so I'm a bit pissy lol


Sent from my iPhone using Tapatalk

[RHKTriton]

Checked under the hood to see where all that coolant on the ground came from.

Looks like the radiator core has finally given up after 208k! Just can't get anything that lasts these days.

[als1200]

Knocked this up for the rear seat area.

[variflex]

Fitted a new SPVi heavy duty clutch due for official release soon




Sent from my iPhone using Tapatalk

How is the new clutch going mate?

[RHKTriton]

Epoxied the leaks on the core, hopefully holds until a replacement can be got in.

Turns out the shroud of the electric fan has been rubbing, even though it had initially been installed with clearance.

These new cores wouldn't last long if you fitted the fan as the manufacturer intended, is with ties through the core.

[dieselweasel]

Finally got round to putting my muffler delete on. I was hoping it wasnt too loud but I'm actually disappointed in how quiet it is. Can't hear any difference from inside the vehicle but the cab had been sound proofed. I had my tiptoe on the gas pedal whilst standing outside and almost can hear a bit of a lower resonation and a gentle turbo whistle but i honestly think its no louder. Happy to have a bit more flow overall. May have to get someone else to drive the wheelbarrow past me standing on the street whilst i listen. Not my wife though, she drives like she's driving miss daisy.